Dacă vrei să ajuți proiectul SuperWrt atunci poți să-ți cumperi routerul wireless tp-link wr1043nd de la EMAG prin butonul din dreapta și un foarte mic procent din prețul obișnuit plătit de tine revine găzduirii site-ului.

Detalii tehnice pentru versiunile hardware 2.x
Procesor: Qualcomm Atheros 720 Mhz MIPS 74Kc
Memorie: 64 MB
Flash: 8 MB
Switch ethernet: Atheros AR8327 rev. 4 (10/100/1000)
Wireless: Atheros AR9550 (trei antene de 5 dBi fiecare) – 20 dBm
Alimentare: 12V – 1,5A

click pentru informații despre placa de bază și procesor

system type		: Qualcomm Atheros QCA9558 rev 0
machine			: TP-LINK TL-WR1043ND v2
processor		: 0
cpu model		: MIPS 74Kc V5.0
BogoMIPS		: 358.80
wait instruction	: yes
microsecond timers	: yes
tlb_entries		: 32
extra interrupt vector	: yes
hardware watchpoint	: yes, count: 4, address/irw mask: [0x0ff8, 0x0ffc, 0x0ff8, 0x0ffb]
isa			: mips1 mips2 mips32r1 mips32r2
ASEs implemented	: mips16 dsp dsp2
shadow register sets	: 1
kscratch registers	: 0
core			: 0
VCED exceptions		: not available
VCEI exceptions		: not available

click pentru informațiile wifi

Wiphy phy0
	max # scan SSIDs: 4
	max scan IEs length: 2257 bytes
	Retry short limit: 7
	Retry long limit: 4
	Coverage class: 0 (up to 0m)
	Device supports AP-side u-APSD.
	Device supports T-DLS.
	Available Antennas: TX 0x7 RX 0x7
	Configured Antennas: TX 0x7 RX 0x7
	Supported interface modes:
		 * IBSS
		 * managed
		 * AP
		 * AP/VLAN
		 * WDS
		 * monitor
		 * mesh point
		 * P2P-client
		 * P2P-GO
	Band 1:
		Capabilities: 0x11ef
			RX LDPC
			HT20/HT40
			SM Power Save disabled
			RX HT20 SGI
			RX HT40 SGI
			TX STBC
			RX STBC 1-stream
			Max AMSDU length: 3839 bytes
			DSSS/CCK HT40
		Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
		Minimum RX AMPDU time spacing: 8 usec (0x06)
		HT TX/RX MCS rate indexes supported: 0-23
		Frequencies:
			* 2412 MHz [1] (20.0 dBm)
			* 2417 MHz [2] (20.0 dBm)
			* 2422 MHz [3] (20.0 dBm)
			* 2427 MHz [4] (20.0 dBm)
			* 2432 MHz [5] (20.0 dBm)
			* 2437 MHz [6] (20.0 dBm)
			* 2442 MHz [7] (20.0 dBm)
			* 2447 MHz [8] (20.0 dBm)
			* 2452 MHz [9] (20.0 dBm)
			* 2457 MHz [10] (20.0 dBm)
			* 2462 MHz [11] (20.0 dBm)
			* 2467 MHz [12] (disabled)
			* 2472 MHz [13] (disabled)
			* 2484 MHz [14] (disabled)
	valid interface combinations:
		 * #{ managed, WDS } <= 2048, #{ AP, mesh point } <= 8, #{ P2P-client, P2P-GO } <= 1, #{ IBSS } <= 1,
		   total <= 2048, #channels <= 1, STA/AP BI must match
		 * #{ IBSS, AP, mesh point } <= 1,
		   total <= 1, #channels <= 1, STA/AP BI must match, radar detect widths: { 20 MHz (no HT), 20 MHz }

	HT Capability overrides:
		 * MCS: ff ff ff ff ff ff ff ff ff ff
		 * maximum A-MSDU length
		 * supported channel width
		 * short GI for 40 MHz
		 * max A-MPDU length exponent
		 * min MPDU start spacing

click pentru pachetele pre-instalate

6in4 - 17-1
6rd - 7-1
base-files - 156-r42228
block-mount - 2014-06-22-e0430f5c62f367e5a8e02755412977b02c3fc45e
busybox - 1.22.1-2
chat - 2.4.6-1
comgt - 0.32-22
davfs2 - 1.5.0-2
ddns-scripts - 1.0.0-22
dnsmasq - 2.71-4
dropbear - 2014.63-1
etherwake - 1.09-3
firewall - 2014-07-19
fstools - 2014-06-22-e0430f5c62f367e5a8e02755412977b02c3fc45e
hd-idle - 1.04-1
hostapd-common - 2014-06-03-1
ip - 3.15.0-1
ip6tables - 1.4.21-1
iptables - 1.4.21-1
iptables-mod-conntrack-extra - 1.4.21-1
iptables-mod-filter - 1.4.21-1
iptables-mod-ipopt - 1.4.21-1
iptables-mod-iprange - 1.4.21-1
iptables-mod-ipv4options - 2.3-1
iptables-mod-led - 1.4.21-1
iptables-mod-tee - 1.4.21-1
iw - 3.15-1
iwinfo - 50
jshn - 2014-07-16-bd388d2b6c2c151bf513c1e449417d18ce02d10b
jsonfilter - 2014-06-19-cdc760c58077f44fc40adbbe41e1556a67c1b9a9
kernel - 3.10.49-1-871c38632a49fd417270ae7becc53fdf
kmod-ath - 3.10.49+2014-05-22-1
kmod-ath9k - 3.10.49+2014-05-22-1
kmod-ath9k-common - 3.10.49+2014-05-22-1
kmod-cfg80211 - 3.10.49+2014-05-22-1
kmod-crypto-aes - 3.10.49-1
kmod-crypto-arc4 - 3.10.49-1
kmod-crypto-core - 3.10.49-1
kmod-crypto-ecb - 3.10.49-1
kmod-crypto-hash - 3.10.49-1
kmod-crypto-manager - 3.10.49-1
kmod-crypto-pcompress - 3.10.49-1
kmod-crypto-sha1 - 3.10.49-1
kmod-fs-ext4 - 3.10.49-1
kmod-fs-hfsplus - 3.10.49-1
kmod-fs-ntfs - 3.10.49-1
kmod-fs-vfat - 3.10.49-1
kmod-fuse - 3.10.49-1
kmod-gpio-button-hotplug - 3.10.49-1
kmod-gre - 3.10.49-1
kmod-ifb - 3.10.49-1
kmod-input-core - 3.10.49-1
kmod-ip6tables - 3.10.49-1
kmod-ipt-conntrack - 3.10.49-1
kmod-ipt-conntrack-extra - 3.10.49-1
kmod-ipt-core - 3.10.49-1
kmod-ipt-filter - 3.10.49-1
kmod-ipt-ipopt - 3.10.49-1
kmod-ipt-iprange - 3.10.49-1
kmod-ipt-ipv4options - 3.10.49+2.3-1
kmod-ipt-led - 3.10.49-1
kmod-ipt-nat - 3.10.49-1
kmod-ipt-nathelper - 3.10.49-1
kmod-ipt-nathelper-extra - 3.10.49-1
kmod-ipt-tee - 3.10.49-1
kmod-iptunnel - 3.10.49-1
kmod-iptunnel4 - 3.10.49-1
kmod-ipv6 - 3.10.49-1
kmod-ledtrig-heartbeat - 3.10.49-1
kmod-ledtrig-netdev - 3.10.49-1
kmod-ledtrig-netfilter - 3.10.49-1
kmod-ledtrig-usbdev - 3.10.49-1
kmod-lib-crc-ccitt - 3.10.49-1
kmod-lib-crc16 - 3.10.49-1
kmod-lib-textsearch - 3.10.49-1
kmod-libphy - 3.10.49-1
kmod-mac80211 - 3.10.49+2014-05-22-1
kmod-mii - 3.10.49-1
kmod-mppe - 3.10.49-1
kmod-nls-base - 3.10.49-1
kmod-nls-cp1250 - 3.10.49-1
kmod-nls-cp1251 - 3.10.49-1
kmod-nls-cp437 - 3.10.49-1
kmod-nls-cp850 - 3.10.49-1
kmod-nls-cp852 - 3.10.49-1
kmod-nls-iso8859-1 - 3.10.49-1
kmod-nls-iso8859-8 - 3.10.49-1
kmod-nls-utf8 - 3.10.49-1
kmod-ppp - 3.10.49-1
kmod-pppoe - 3.10.49-1
kmod-pppox - 3.10.49-1
kmod-pptp - 3.10.49-1
kmod-sched-connmark - 3.10.49-1
kmod-sched-core - 3.10.49-1
kmod-scsi-core - 3.10.49-1
kmod-sit - 3.10.49-1
kmod-slhc - 3.10.49-1
kmod-sound-core - 3.10.49-1
kmod-tun - 3.10.49-1
kmod-usb-acm - 3.10.49-1
kmod-usb-audio - 3.10.49-1
kmod-usb-core - 3.10.49-1
kmod-usb-net - 3.10.49-1
kmod-usb-net-asix - 3.10.49-1
kmod-usb-net-cdc-eem - 3.10.49-1
kmod-usb-net-cdc-ether - 3.10.49-1
kmod-usb-net-cdc-mbim - 3.10.49-1
kmod-usb-net-cdc-ncm - 3.10.49-1
kmod-usb-net-cdc-subset - 3.10.49-1
kmod-usb-net-dm9601-ether - 3.10.49-1
kmod-usb-net-hso - 3.10.49-1
kmod-usb-net-ipheth - 3.10.49-1
kmod-usb-net-mcs7830 - 3.10.49-1
kmod-usb-net-pegasus - 3.10.49-1
kmod-usb-net-qmi-wwan - 3.10.49-1
kmod-usb-net-rndis - 3.10.49-1
kmod-usb-net-sierrawireless - 3.10.49-1
kmod-usb-ohci - 3.10.49-1
kmod-usb-printer - 3.10.49-1
kmod-usb-serial - 3.10.49-1
kmod-usb-serial-ipw - 3.10.49-1
kmod-usb-serial-motorola-phone - 3.10.49-1
kmod-usb-serial-option - 3.10.49-1
kmod-usb-serial-qualcomm - 3.10.49-1
kmod-usb-serial-sierrawireless - 3.10.49-1
kmod-usb-serial-wwan - 3.10.49-1
kmod-usb-storage - 3.10.49-1
kmod-usb-wdm - 3.10.49-1
kmod-usb2 - 3.10.49-1
kmod-video-core - 3.10.49-1
kmod-video-uvc - 3.10.49-1
kmod-video-videobuf2 - 3.10.49-1
l7-protocols - 2009-05-28-2
libblobmsg-json - 2014-07-16-bd388d2b6c2c151bf513c1e449417d18ce02d10b
libc - 0.9.33.2-1
libexpat - 2.1.0-1
libfuse - 2.9.0-2
libgcc - 4.8-linaro-1
libip4tc - 1.4.21-1
libip6tc - 1.4.21-1
libiwinfo - 50
libiwinfo-lua - 50
libjson-c - 0.11-2
libjson-script - 2014-07-16-bd388d2b6c2c151bf513c1e449417d18ce02d10b
liblua - 5.1.5-1
libneon - 0.29.6-2
libnfnetlink - 1.0.1-1
libnl-tiny - 0.1-3
libopenssl - 1.0.1i-1
libpolarssl - 1.3.8-1
libpthread - 0.9.33.2-1
librt - 0.9.33.2-1
libubox - 2014-07-16-bd388d2b6c2c151bf513c1e449417d18ce02d10b
libubus - 2014-07-03-f688c7ad0b2435a89bfd13f5496cabf596b54c8f
libubus-lua - 2014-07-03-f688c7ad0b2435a89bfd13f5496cabf596b54c8f
libuci - 2014-04-11.1-1
libuci-lua - 2014-04-11.1-1
libusb-1.0 - 1.0.9-1
libustream-polarssl - 2014-03-25-fc0b5ec804ee43c532978dd04ab0509c34baefb0
libxtables - 1.4.21-1
lua - 5.1.5-1
luci - svn-r10520-1
luci-app-commands - svn-r10520-1
luci-app-ddns - svn-r10520-1
luci-app-firewall - svn-r10520-1
luci-app-hd-idle - svn-r10520-1
luci-app-mwan3 - 1.3-1
luci-app-p910nd - svn-r10520-1
luci-app-qos - svn-r10520-1
luci-app-samba - svn-r10520-1
luci-app-upnp - svn-r10520-1
luci-app-wol - svn-r10520-1
luci-base - svn-r10520-1
luci-lib-nixio - svn-r10520-1
luci-mod-admin-full - svn-r10520-1
luci-proto-3g - svn-r10520-1
luci-proto-ipv6 - svn-r10520-1
luci-proto-ppp - svn-r10520-1
luci-proto-relay - svn-r10520-1
luci-ssl - svn-r10520-1
luci-theme-bootstrap - svn-r10520-1
luci-theme-openwrt - svn-r10520-1
miniupnpd - 1.8.20140523-4
mtd - 20
mwan3 - 1.5-3
netifd - 2014-08-13-732074385389b1bb766a0b09b967d6883c357813
odhcp6c - 2014-07-21-67b311ab81736b35858664219d345844ab08fcc7
odhcpd - 2014-08-19-710744ecea73b6a3cf560776e298741b04fb727a
opkg - 9c97d5ecd795709c8584e972bfdf3aee3a5b846d-7
p910nd - 0.95-3
ppp - 2.4.6-1
ppp-mod-pppoe - 2.4.6-1
ppp-mod-pptp - 2.4.6-1
procd - 2014-07-30-35e01a9601292b2f609e65c2ddb3990cba8f378e
px5g - 1
qos-scripts - 1.2.1-6
relayd - 2014-06-29-8b20ffae06b9b7fcc6fb52d3b8a80b45ed424e39
resolveip - 2
restorefactory - 1-6
samba36-server - 3.6.24-1
swconfig - 10
tc - 3.15.0-1
uboot-envtools - 2014.04-4
ubox - 2014-05-30-c3d4118eee505f41c4d20a87f326479530837569
ubus - 2014-07-03-f688c7ad0b2435a89bfd13f5496cabf596b54c8f
ubusd - 2014-07-03-f688c7ad0b2435a89bfd13f5496cabf596b54c8f
uci - 2014-04-11.1-1
uhttpd - 2014-06-11-dabd7dea6445aaa0e5b8d9add1872fa7393b3a85
uhttpd-mod-ubus - 2014-06-11-dabd7dea6445aaa0e5b8d9add1872fa7393b3a85
uqmi - 2014-05-27-d7a56cad6d6ef3c2a5602fc604e31999eb9e78fa
usb-modeswitch - 2014-07-18-01ecc3b9764d1dd89cf36ede0a2d98f9adb0cd33
wpad-mini - 2014-06-03-1
zlib - 1.2.8-1

Atenție ! Nu mai am versiunea asta hardware de router și nu mai pot testa firmware-ul dar ar trebui să funcționeze.. Folosiți pe propria răspundere !


Atenție! Viteza de transfer între WAN și LAN cu SuperWrt se bazează doar pe CPU în lipsa facilității “hardware nat” oferită în firmware-ul original și ca atare performanțele de obicei nu depășesc aproximativ 300 Mbit/s !

SuperWrt nu e recomandat (deocamdată) celor care au contractat abonamentele Fiberlink 500 sau Fiberlink 1000 !

tp-link_wr1043nd_v2_three_wireless
tp-link_wr1043nd_v2_front_leds
tp-link_wr1043nd_v2_back_ports

Acest articol are 111 comentarii

  1. George

    Salut ,vreau sa iti multumesc pentru firmware este excelent si in acelasi timp sa semnalez o problema . Viteza atinsa pe wireless este mai slaba decat pe firmware original cu setarea de 450 mbs , pe fir merge excelent .Poate mai apar ceva drivere noi la wireless ,banuiesc ca nu il foloseste la 450 mbs superwrt-ul ,viteza wireless fiind identica cu oficialul fara setarea de 450 mbs .Am uitat sa precizez ca folosesc 1043nd v2 .

    1. SuperWrt

      Salut George,
      ai încercat și cu HT40 ? și distance optimization ?

  2. George

    Sal , da am incercat vitezele sant cu 30-30 mbit/s mai mici pe super wrt.

  3. ov1d1u

    Salut, mai menţii repository-ul pentru versiunea ta de OpenWRT? Momentan văd că returnează 404. Mersi

    1. SuperWrt

      Salut,
      http://www.ip6.ro și repository-urile vechi sunt dezactivate de câteva luni bune,
      îți recomand să folosești un firmware mai recent cu repository-ul oficial OpenWrt.

  4. bogdan

    Sal,

    De ce nu mai pui si md5-ul firmware-ului pe site? Cred ca nginx-ul are un plugin care face automat pentru fisiere. Daca dai acces la /download iti arata intr-o coloana separata.

  5. LiviuC

    Salutare, nu reusesc sa fac sa mearga overlay. A reusit cineva? (hw v2.1, r39450)

    1. LiviuC

      Rezolvat, merge sa utilizeze tot ‘/’, nu doar ‘/overlay’. Acuma vede rootfs-ul mare cat stickul :). In ‘/etc/config/fstab’ am pus doar uuid-ul, n-am mai pus si ‘target’

  6. Gabi

    “SuperWrt nu e recomandat (deocamdată) celor care au contractat abonamentele Fiberlink 500 sau Fiberlink 1000 !”

    Intrebare: De ce?

    Ps: Nerecomandarea e valabila si pentru Fiberlink 100?

    1. SuperWrt

      Pentru că nu are modificările în kernel și netfilter pentru facilitatea numită “Hardware NAT”. Pentru FL50/FL100 e mai mult decât perfect.

  7. emil

    scsi 0:0:0:0: Direct-Access FUJITSU MHV2120BH PL PQ: 0 ANSI: 2 CCS
    sd 0:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/111 GiB)
    sd 0:0:0:0: [sda] Write Protect is off
    sd 0:0:0:0: [sda] Mode Sense: 00 38 00 00
    sd 0:0:0:0: [sda] Asking for cache data failed
    sd 0:0:0:0: [sda] Assuming drive cache: write through
    jffs2: notice: (371) jffs2_build_xattr_subsystem: complete building xattr subsystem, 3 of xdatum (1 unchecked, 2 orphan) and 27 of xref (0 dead, 2 orphan) found.
    sd 0:0:0:0: [sda] Asking for cache data failed
    sd 0:0:0:0: [sda] Assuming drive cache: write through
    jffs2: notice: (368) jffs2_build_xattr_subsystem: complete building xattr subsystem, 3 of xdatum (1 unchecked, 2 orphan) and 27 of xref (0 dead, 2 orphan) found.
    eth0: link down
    sda: sda1
    sd 0:0:0:0: [sda] Asking for cache data failed
    sd 0:0:0:0: [sda] Assuming drive cache: write through
    sd 0:0:0:0: [sda] Attached SCSI disk
    EXT4-fs (sda): Filesystem with huge files cannot be mounted RDWR without CONFIG_LBDAF)…………………………..care este rezolvarea

    1. SuperWrt

      Salut emil,
      ai formatat partiția cu huge_file, dacă nu ai nevoie de fișiere mai mari de 2 TB atunci poți încerca tune2fs -O ^huge_file /dev/sdaX pe respectiva partiție ne-montată.

  8. claudiu

    Am pus SuperWrt r39717 si merge pe DHCP dar cand incerc pe Static IP nu se conecteaza. Am avut un 1043nd v.1 cu ddwrt si era mult mai usor de setat. Am editat conexiunea tip ppoe cu care vine firmware-ul, am pus ip-ul cu gateway si dns, am pus mac-ul placii de baza, dar nu reusesc sa ma conectez. Ce imi scapa?

  9. Florin

    Salutam.
    Am instalat superwrt pe 1043ND V2.
    dar nu pot face wirelessul functional imi apare :Wireless is disabled or not associated

    nu e prima data cand ma joc cu setarile aceastea, dar nu inteleg ce fac gresit.

    1. SuperWrt

      Salut,
      via ssh (conectat pe ethernet LAN) poți șterge /etc/config/wireless și rula apoi wifi detect > /etc/config/wireless după care editezi opțiunile dorite și activezi cu wifi.

    2. Florin

      revenind, vad ca doar pe canalul 13 unde stateam de obicei mi-a facut asa.
      Am dat pe 1 si nu mai sunt probleme.
      Daca pun pe 13 din nou: Wireless is disabled or not associated
      Ma rog il las pe 1.
      Buna treaba !
      Succes in continuare.

  10. Doru

    Am citit cam tot ce era de citit despre 1043ND.
    Ceea ce ma intereseaza este sa-l folosesc impreuna cu un modem 3G de la RDS.
    Procedurile de adaugare de pachete/drivere sunt destul de alambicate pentru cei neexperimentati cu linii de comanda si familiarizati cu stilul linux.
    Exista un firmware care sa contina deja facilitatile samba, print server, 3G modem pe langa functionalitatile de baza ale routerului (wan, lan, nat, vpn, ddns, wi-fi)?

  11. emil

    se poate ca la fiecare upgrade de kernel sa pui si changelog..

  12. Anon

    Atenție! Viteza de transfer între WAN și LAN cu SuperWrt se bazează doar pe CPU în lipsa facilității “hardware nat” oferită în firmware-ul original și ca atare performanțele de obicei nu depășesc aproximativ 300 Mbit/s !

    E valabil si pentru revizia v2 a router-ului ?

  13. lori

    Am instalat Superwrt pe un 1043nd, v1, abandonand Gargoyle, pentru a beneficia de WOL (in gargoyle se pierdea adresa MAC, ajungea 0:0:0:0:0:0. Totul a mers fara probleme, atat instalarea, cat si configurarea( DDNS, port forward, WOL).

    Acelasi lucru si cu un wr740n, su cu acesta, totul ok.

  14. ovidiu

    Am pus superwrt pe 1043 nd v.2 si nu reusesc sa il fac sa mearga pe ftp. Ma puteti ajuta?

  15. Razvan

    Dupa mai bine de 2 ani de folosire OpenWRT/SuperWRT am revenit la firmware original. Aceasta revenire a fost cauzata de faptul ca trebuia sa resetez router-ul cel putin odata pe zi deoarece nu mai mergea wireless-ul. De cand am revenit la softul original merge in continuu(10 zile) fara probleme. Performanta wireless si lan este aceeasi, iar, stabilitatea este mult mai buna. Singura functie care imi lipseste este wake on lan-ul care nu il are implementat.

    1. SuperWrt Geek

      Salut Razvan,
      probabil că e vorba de versiunea 1, am avut și eu probleme cu două routere v1, alții văd că n-au avut..
      Probabil e o anumită subversiune mai aiurea, e important că tu ai ales cea mai bună variantă pentru tine.

  16. ithanium2

    Salut, Am un TL-1043ND versiunea 1 (cea veche) si mai mult de 85-87 mbps nu merge. Am firmware-urile tale de mai bine de un an si pana acuma n-am simtit limitarea pentru ca aveam un abonament de la UPC de 60mbit. Acum am trecut la cel de 150mbit.
    Cu un firmware mai vechi (de anul trecut cred), stiu ca a mers bine, peste 100mbit (stiu pentru ca mi-au dat un fel de trial la abonamentul de 120mbit).

    1. SuperWrt Geek

      Salut,
      85-87 Mbit/s via wireless sau ethernet ? Să nu fie una din versiunile hardware cu probleme la portul WAN..
      Oricum recomandarea ar fi transformarea ăstuia într-un AP și cumpărarea de wr1043nd v2 !

      1. ithanium2

        Salut, Vitezele sunt pe Ethernet. Routerul nu are nici o problema, merge perfect si am uptime excelent la el (pica doar cand se ia curentul :) ), deci nu am de gand sa il inlocuiesc.
        Sunt sigur ca problema e undeva in firmware. Am avut un firmware mai vechi tot de-al tau si mergea mai bine.
        Ciudat este ca si cu ultimul firmware stock duce doar 100mbit.

        Dar am rezolvat problema. Am instalat OpenWRT Attitude Adjustment 12.9 (varianta oficiala) si merge la viteza maxima a conexiunii (150mbil). Deci problema e undeva in firmware.

        1. ithanium2

          Salut din nou,
          A trebuit sa revin la firmware-ul tau deoarece pe Attitude Adjustment face figuri wireless-ul, in sensul ca merge destul de greu dupa un anumit timp si trebuie restartat routerul. Culmea, pe wired merge perfect.

          Dar sincer sa fiu nu inteleg care este problema la versiunea ta de firmware si de ce nu reuseste sa mearga cu mai mult de 80mbit wired.

          1. SuperWrt Geek

            Salut, verifică garantările default generate de qos-scripts, eventual oprește-le, dacă la fel se comportă nu pot decât să-ți recomand wr1043nd v2..

  17. ithanium2

    Am reusit sa il semi-brickuiesc :) Am instalat un firmware cu mai multe features si merge foarte greu luci…abia ma lasa sa ma loghez…cand ii dau pe tab-ul de update firmware face overload si crapa…se reseteaza.

    Ajuta-ma cu un sfat te rog. Ce sa aleg intre 1043ND v.2 si WDR3600? Intreb prin prisma daca as putea sa il transform intr-un mini-NAS/TorrentBox. Tind sa cred ca, cei 128MB ram din WDR3600 sunt mai importanti decat frecventa CPU mai ridicata de pe 1043ND.

    1. SuperWrt Geek

      Salut, wdr3600 ar fi o alegere mai bună, ramul contează pentru ce vrei să faci iar cele două usb-uri alimentează și funcționează fără probleme.

      1. ithanium2

        Pai oricum o sa folosesc un HDD de 3.5″ deci trebuie sa iau rack cu alimentare, asa ca USB-ul n-o sa fie stresat.
        Ce ma intreb eu este daca face fata la Transmission sau o sa se blocheze?

  18. lori

    Salut!

    Am testat din nou ipv6 (http://www.test-ipv6.ro/), si am constatat ca nu functioneaza (No ipv6 address detected).
    Am o interfata wan6, dar nu se conecteaza. Cum trebuie sa fie, dhcpv6, sau tot ppoe, ca la ipv4? (RDS). sau nu trebuie interfata separat fata de ipv4?

    MAC-Address: 00:00:00:00:00:00
    RX: 0.00 B (0 Pkts.)
    TX: 0.00 B (0 Pkts.)

    Routerul e 1043 v1.

    1. SuperWrt Geek

      Interfața WAN6 NU se configurează manual. Suportul IPv6 e preconfigurat pentru Fiberlink.

  19. C

    Buna, folosesc SuperWrt de luni bune si sint foarte multumit de el ,dar am trecut la abonament de 200MB de la rds si cind pun semnalul prin router 1043 V1.08 nu depasesc 100MB dar cind pun pe autentificare directa fara router ajung la 200MB .
    Ce este de facut ? ca am nevoie de router sa pot acesa netul din toate casa pe fir… ceva sugestii??

    1. SuperWrt Geek

      Salut, wr1043nd v1 e o platformă veche cu un CPU slăbuț, n-o să ai niciodată mai mult de 150-170 Mbit/s WAN – LAN așadar poți trece la un router mai rapid..

  20. Razvan

    Stii cumva o rezolvare pentru eroarea aceasta: “ath: phy0: Failed to stop TX DMA, queues=0x004!” Dupa ce da eroarea aceasta nu ma mai pot conecta la router, decat daca pornesc si opresc wirelessul. Din ce am gasit pe internet nu era nicio rezolvare concreta.

    1. SuperWrt Geek

      Salut Răzvan,
      cred că s-a rezolvat problema, poți încerca ultima versiune de SuperWrt.

  21. George

    Salut,
    Am cumparat si eu de trei zile 1043 nd-ul si pana acum m-a suparat rau, se blocheaza la doua-trei ore, semnalul pe radio este mai slab decat aveam pe un asus care a decedat dupa 6 ani de folosinta continua.
    in dimineata asta am pus si eu wrt-ul, la prima strigare semnal pe radio pare mai bun, nu stiu inca de stabilitate, dar o alta problema mare zic eu, dupa fiecare restart sau scos din priza pierde setarile si trebuie setat din nou si pe wan si pe wirless. ???? am gresit eu undeva ??

    1. SuperWrt Geek

      Salut George,
      n-am văzut sau auzit de un asemenea comportament cu SuperWrt pe tp-link wr1043nd.
      Save and Apply sau uci commit ar trebui să scrie modificările în flash fără probleme.

      1. George

        initial am pus versiunea din upgrade, acum am pus versiunea din prima instalare (aia de 7,75MB) si vad ca acum memoreaza setarile, i-am dat reboot, l-am scos si din priza si este ok.

  22. George

    ma gandesc ca ar putea fi defect, din pacate ni am fost prea grijuliu cu el si nu am pastrat nici ambalajul original.

  23. George

    Cred ca am rezolvat problema cu blocatul, am inlocuit alimentatorul original cu altul pe care il aveam eu de 12 V si 1, 25 Ah, cel original era de 1, 5 Ah, cred ca ala original nu-si facea treba, sunt aproape 48 de ore de cand nu s-a mai blocat de loc.

  24. Radu

    Salut
    Pentru un 1043nd ver v2, exista posibilitatea ca dupa instalarea superwrt sa obtin un semnal wireless mai bun ( transfer mai mare) .?
    Exista limitare pe wireless din softul original? (putere ,viteza etc)

  25. Dani

    Salut, am si eu o intrebare.. daca trec de pe factory router pe acest SuperWRT, in momentul in care fac upgrade, mi se va instala luci singur ? sau va trebuii sa il instalez eu dupa ?

  26. CloZee

    Found one bug.

    Under the Network – > Wifi the “Scan” doesn’t work.

    This page contains the following errors:
    error on line 112 at column 89: AttValue: ‘ expected
    Below is a rendering of the page up to the first error.

    1. SuperWrt Geek

      Thanks for your message but hang on: i’m recompiling and testing the updated firmware on my routers as we speak, maybe they fixed the bug in LuCi.. In 2-3 hours builds should be updated on the site.
      P.S. How do you like the english version of the site? I bought WPML and translated router pages and some others..

      1. CloZee

        Okey.

        I like it. It’s enough for an openwrt project.

    2. SuperWrt Geek

      Seems like the same bug is still present. Can you please upload a screenshot of the broken page in a comment? thanks.

  27. dan

    BARRIER BREAKER (14.07, r42096)
    —————————————————–
    OpenWrt custom firmware – http://www.superwrt.eu
    —————————————————–
    root@an0nym0us:~# opkg update
    Downloading http://downloads.openwrt.org/snapshots/trunk/ar71xx/packages/Packages.gz.
    wget: server returned error: HTTP/1.1 404 Not Found
    Collected errors:
    * opkg_download: Failed to download http://downloads.openwrt.org/snapshots/trunk/ar71xx/packages/Packages.gz, wget returned 1.

    Structura lor de directoare este:
    ../
    base/ 10-Aug-2014 02:24 –
    luci/ 10-Aug-2014 02:24 –
    management/ 10-Aug-2014 02:24 –
    packages/ 10-Aug-2014 02:25 –
    routing/ 10-Aug-2014 02:25 –
    telephony/ 10-Aug-2014 02:25 –

    /etc/opkg.conf
    dest root /
    dest ram /tmp
    lists_dir ext /var/opkg-lists
    option overlay_root /overlay
    src/gz barrier_breaker http://downloads.openwrt.org/snapshots/trunk/ar71xx/packages

    Nu stiu ce sa ii fac.
    Multumesc.

    1. SuperWrt Geek

      Am pus un tichet în bug trackerul OpenWrt, cum avem o soluție de la developeri actualizez și eu firmware-ul pe site, mersi pentru raport.

  28. Laurentiu

    Salut cum pot obtine 4to6 pentru ipv6 ??? updatul nu merge asa ca nu il pot instala automat
    iar eu imi iau ip-urile v6 de la tunnelbroker

      1. Laurentiu

        Ms de raspunsul rapid si de tutorial dar nu functioneaza
        Address: 2001:470:1f1a:1b::2/128
        Gateway: 0:0:0:0:0:0:0:0
        Connected: 0h 3m 32s
        nu detecteaza gateway
        m-am tot uitat pe aici si pe acolo dar nu stiu cum sa il adaug manual

  29. Laurentiu

    am gasit un bug daca dai scan la wifi

    This page contains the following errors:
    error on line 112 at column 89: AttValue: ‘ expected
    Below is a rendering of the page up to the first error.
    ps
    am reusit cu ipv6

  30. Iry

    Am intrat astazi in posesia unui TP Link 1043 ND V1.0 (un amic m-a rugat sa-i instalez si lui suport pt IPV 6).Eu avand deja acelasi router dar V2 , care ruleaza de multe luni versiunea ta. Intrebarea mea este: Teoretic ar fi vreo problema daca ,,urc” pe aceasta versiune V1 varianta Luci ?

    1. SuperWrt Geek

      Sunt două platforme diferite, nu i-l strica. Dacă vrei neapărat să-i pui SuperWrt îți fac o imagine mâine seară.

      1. Iry

        Multumesc.In seara asta il urc pe device.

        1. iRY

          Am o problema.Nu mi se conecteaza la PPOE.Am verificat si resetat parola dar nu vrea sa conecteze.Gresec eu ceva?Atasez si log.

          ==========================================
          Mon Aug 18 18:41:29 2014 kern.info kernel: usbcore: registered new interface driver usbfs
          Mon Aug 18 18:41:29 2014 kern.info kernel: usbcore: registered new interface driver hub
          Mon Aug 18 18:41:29 2014 kern.info kernel: usbcore: registered new device driver usb
          Mon Aug 18 18:41:29 2014 kern.notice kernel: SCSI subsystem initialized
          Mon Aug 18 18:41:29 2014 kern.info kernel: ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
          Mon Aug 18 18:41:29 2014 kern.info kernel: ehci-platform: EHCI generic platform driver
          Mon Aug 18 18:41:29 2014 kern.info kernel: ehci-platform ehci-platform: EHCI Host Controller
          Mon Aug 18 18:41:29 2014 kern.info kernel: ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
          Mon Aug 18 18:41:29 2014 kern.info kernel: ehci-platform ehci-platform: irq 3, io mem 0x1b000000
          Mon Aug 18 18:41:29 2014 kern.info kernel: ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00
          Mon Aug 18 18:41:29 2014 kern.info kernel: hub 1-0:1.0: USB hub found
          Mon Aug 18 18:41:29 2014 kern.info kernel: hub 1-0:1.0: 1 port detected
          Mon Aug 18 18:41:29 2014 kern.info kernel: ohci_hcd: USB 1.1 ‘Open’ Host Controller (OHCI) Driver
          Mon Aug 18 18:41:29 2014 kern.info kernel: usbcore: registered new interface driver usb-storage
          Mon Aug 18 18:41:29 2014 kern.info kernel: NET: Registered protocol family 10
          Mon Aug 18 18:41:29 2014 kern.info kernel: NTFS driver 2.1.30 [Flags: R/O MODULE].
          Mon Aug 18 18:41:29 2014 kern.info kernel: tun: Universal TUN/TAP device driver, 1.6
          Mon Aug 18 18:41:29 2014 kern.info kernel: tun: (C) 1999-2004 Max Krasnyansky
          Mon Aug 18 18:41:29 2014 kern.info kernel: sit: IPv6 over IPv4 tunneling driver
          Mon Aug 18 18:41:29 2014 kern.info kernel: gre: GRE over IPv4 demultiplexor driver
          Mon Aug 18 18:41:29 2014 kern.info kernel: ip_gre: GRE over IPv4 tunneling driver
          Mon Aug 18 18:41:29 2014 kern.info kernel: nf_conntrack version 0.5.0 (460 buckets, 1840 max)
          Mon Aug 18 18:41:29 2014 kern.info kernel: ip6_tables: (C) 2000-2006 Netfilter Core Team
          Mon Aug 18 18:41:29 2014 kern.info kernel: Linux video capture interface: v2.00
          Mon Aug 18 18:41:29 2014 kern.info kernel: u32 classifier
          Mon Aug 18 18:41:29 2014 kern.info kernel: input device check on
          Mon Aug 18 18:41:29 2014 kern.info kernel: Actions configured
          Mon Aug 18 18:41:29 2014 kern.info kernel: Mirror/redirect action on
          Mon Aug 18 18:41:29 2014 kern.info kernel: fuse init (API version 7.22)
          Mon Aug 18 18:41:29 2014 kern.info kernel: usbcore: registered new interface driver cdc_acm
          Mon Aug 18 18:41:29 2014 kern.info kernel: cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
          Mon Aug 18 18:41:29 2014 kern.info kernel: usbcore: registered new interface driver cdc_wdm
          Mon Aug 18 18:41:29 2014 kern.info kernel: Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
          Mon Aug 18 18:41:29 2014 kern.info kernel: Backport generated by backports.git backports-20140320-37-g5c33da0
          Mon Aug 18 18:41:29 2014 kern.info kernel: ip_tables: (C) 2000-2006 Netfilter Core Team
          Mon Aug 18 18:41:29 2014 kern.info kernel: usbcore: registered new interface driver ipheth
          Mon Aug 18 18:41:29 2014 kern.info kernel: pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver
          Mon Aug 18 18:41:29 2014 kern.info kernel: usbcore: registered new interface driver pegasus
          Mon Aug 18 18:41:29 2014 kern.info kernel: usbcore: registered new interface driver usblp
          Mon Aug 18 18:41:29 2014 kern.info kernel: usbcore: registered new interface driver usbserial
          Mon Aug 18 18:41:29 2014 kern.info kernel: usbcore: registered new interface driver usbserial_generic
          Mon Aug 18 18:41:29 2014 kern.info kernel: usbserial: USB Serial support registered for generic
          Mon Aug 18 18:41:29 2014 kern.info kernel: uvcvideo: Unable to create debugfs directory
          Mon Aug 18 18:41:29 2014 kern.info kernel: usbcore: registered new interface driver uvcvideo
          Mon Aug 18 18:41:29 2014 kern.info kernel: USB Video Class driver (1.1.1)
          Mon Aug 18 18:41:29 2014 kern.info kernel: xt_time: kernel timezone is -0000
          Mon Aug 18 18:41:29 2014 kern.info kernel: usbcore: registered new interface driver asix
          Mon Aug 18 18:41:29 2014 kern.info kernel: usbcore: registered new interface driver cdc_ether
          Mon Aug 18 18:41:29 2014 kern.info kernel: usbcore: registered new interface driver cdc_subset
          Mon Aug 18 18:41:29 2014 kern.info kernel: usbcore: registered new interface driver dm9601
          Mon Aug 18 18:41:29 2014 kern.info kernel: cfg80211: Calling CRDA to update world regulatory domain
          Mon Aug 18 18:41:29 2014 kern.info kernel: cfg80211: World regulatory domain updated:
          Mon Aug 18 18:41:29 2014 kern.info kernel: cfg80211: DFS Master region: unset
          Mon Aug 18 18:41:29 2014 kern.info kernel: cfg80211: (start_freq – end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
          Mon Aug 18 18:41:29 2014 kern.info kernel: cfg80211: (2402000 KHz – 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
          Mon Aug 18 18:41:29 2014 kern.info kernel: cfg80211: (2457000 KHz – 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
          Mon Aug 18 18:41:29 2014 kern.info kernel: cfg80211: (2474000 KHz – 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
          Mon Aug 18 18:41:29 2014 kern.info kernel: cfg80211: (5170000 KHz – 5250000 KHz @ 160000 KHz), (N/A, 2000 mBm), (N/A)
          Mon Aug 18 18:41:29 2014 kern.info kernel: cfg80211: (5250000 KHz – 5330000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
          Mon Aug 18 18:41:29 2014 kern.info kernel: cfg80211: (5490000 KHz – 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
          Mon Aug 18 18:41:29 2014 kern.info kernel: cfg80211: (5735000 KHz – 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
          Mon Aug 18 18:41:29 2014 kern.info kernel: cfg80211: (57240000 KHz – 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
          Mon Aug 18 18:41:29 2014 kern.info kernel: usbcore: registered new interface driver MOSCHIP usb-ethernet driver
          Mon Aug 18 18:41:29 2014 kern.info kernel: usbcore: registered new interface driver moto_modem
          Mon Aug 18 18:41:29 2014 kern.info kernel: usbserial: USB Serial support registered for moto-modem
          Mon Aug 18 18:41:29 2014 kern.info kernel: PPP generic driver version 2.4.2
          Mon Aug 18 18:41:29 2014 kern.info kernel: PPP MPPE Compression module registered
          Mon Aug 18 18:41:29 2014 kern.info kernel: NET: Registered protocol family 24
          Mon Aug 18 18:41:29 2014 kern.info kernel: PPTP driver version 0.8.5
          Mon Aug 18 18:41:29 2014 kern.info kernel: usbcore: registered new interface driver qmi_wwan
          Mon Aug 18 18:41:29 2014 kern.info kernel: usbcore: registered new interface driver rndis_host
          Mon Aug 18 18:41:29 2014 kern.info kernel: usbcore: registered new interface driver sierra
          Mon Aug 18 18:41:29 2014 kern.info kernel: usbserial: USB Serial support registered for Sierra USB modem
          Mon Aug 18 18:41:29 2014 kern.info kernel: usbcore: registered new interface driver sierra_net
          Mon Aug 18 18:41:29 2014 kern.info kernel: usbcore: registered new interface driver snd-usb-audio
          Mon Aug 18 18:41:29 2014 kern.info kernel: usbcore: registered new interface driver ipw
          Mon Aug 18 18:41:29 2014 kern.info kernel: usbserial: USB Serial support registered for IPWireless converter
          Mon Aug 18 18:41:29 2014 kern.info kernel: usbcore: registered new interface driver option
          Mon Aug 18 18:41:29 2014 kern.info kernel: usbserial: USB Serial support registered for GSM modem (1-port)
          Mon Aug 18 18:41:29 2014 kern.debug kernel: ath: EEPROM regdomain: 0x0
          Mon Aug 18 18:41:29 2014 kern.debug kernel: ath: EEPROM indicates default country code should be used
          Mon Aug 18 18:41:29 2014 kern.debug kernel: ath: doing EEPROM country->regdmn map search
          Mon Aug 18 18:41:29 2014 kern.debug kernel: ath: country maps to regdmn code: 0x3a
          Mon Aug 18 18:41:29 2014 kern.debug kernel: ath: Country alpha2 being used: US
          Mon Aug 18 18:41:29 2014 kern.debug kernel: ath: Regpair used: 0x3a
          Mon Aug 18 18:41:29 2014 kern.debug kernel: ieee80211 phy0: Selected rate control algorithm ‘minstrel_ht’
          Mon Aug 18 18:41:29 2014 kern.info kernel: ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2133 RF Rev:a2 mem=0xb80c0000, irq=2
          Mon Aug 18 18:41:29 2014 kern.info kernel: cfg80211: Calling CRDA for country: US
          Mon Aug 18 18:41:29 2014 kern.info kernel: cfg80211: Regulatory domain changed to country: US
          Mon Aug 18 18:41:29 2014 kern.info kernel: cfg80211: DFS Master region: FCC
          Mon Aug 18 18:41:29 2014 kern.info kernel: cfg80211: (start_freq – end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
          Mon Aug 18 18:41:29 2014 kern.info kernel: cfg80211: (2402000 KHz – 2472000 KHz @ 40000 KHz), (N/A, 3000 mBm), (N/A)
          Mon Aug 18 18:41:29 2014 kern.info kernel: cfg80211: (5170000 KHz – 5250000 KHz @ 80000 KHz), (N/A, 1700 mBm), (N/A)
          Mon Aug 18 18:41:29 2014 kern.info kernel: cfg80211: (5250000 KHz – 5330000 KHz @ 80000 KHz), (N/A, 2300 mBm), (0 s)
          Mon Aug 18 18:41:29 2014 kern.info kernel: cfg80211: (5735000 KHz – 5835000 KHz @ 80000 KHz), (N/A, 3000 mBm), (N/A)
          Mon Aug 18 18:41:29 2014 kern.info kernel: cfg80211: (57240000 KHz – 63720000 KHz @ 2160000 KHz), (N/A, 4000 mBm), (N/A)
          Mon Aug 18 18:41:29 2014 kern.err kernel: overlayfs: ERROR – failed to whiteout ’00_uhttpd_ubus’
          Mon Aug 18 18:41:29 2014 kern.err kernel: overlayfs: ERROR – failed to whiteout ’01_leds’
          Mon Aug 18 18:41:29 2014 kern.err kernel: overlayfs: ERROR – failed to whiteout ’02_network’
          Mon Aug 18 18:41:29 2014 kern.err kernel: overlayfs: ERROR – failed to whiteout ’03_network-switchX-migration’
          Mon Aug 18 18:41:29 2014 kern.err kernel: overlayfs: ERROR – failed to whiteout ’03_network-vlan-migration’
          Mon Aug 18 18:41:29 2014 kern.err kernel: overlayfs: ERROR – failed to whiteout ’04_led_migration’
          Mon Aug 18 18:41:29 2014 kern.err kernel: overlayfs: ERROR – failed to whiteout ’09_fix-seama-header’
          Mon Aug 18 18:41:29 2014 kern.err kernel: overlayfs: ERROR – failed to whiteout ’09_fix-trx-header’
          Mon Aug 18 18:41:29 2014 kern.err kernel: overlayfs: ERROR – failed to whiteout ’10-fstab’
          Mon Aug 18 18:41:29 2014 kern.err kernel: overlayfs: ERROR – failed to whiteout ’10_migrate-shadow’
          Mon Aug 18 18:41:29 2014 kern.err kernel: overlayfs: ERROR – failed to whiteout ’11_migrate-sysctl’
          Mon Aug 18 18:41:29 2014 kern.err kernel: overlayfs: ERROR – failed to whiteout ’12_network-generate-ula’
          Mon Aug 18 18:41:29 2014 kern.err kernel: overlayfs: ERROR – failed to whiteout ’30_uboot-envtools’
          Mon Aug 18 18:41:29 2014 kern.err kernel: overlayfs: ERROR – failed to whiteout ’50-restorefactory’
          Mon Aug 18 18:41:29 2014 kern.err kernel: overlayfs: ERROR – failed to whiteout ’99-miniupnpd’
          Mon Aug 18 18:41:29 2014 kern.err kernel: overlayfs: ERROR – failed to whiteout ‘luci-hd_idle’
          Mon Aug 18 18:41:29 2014 kern.err kernel: overlayfs: ERROR – failed to whiteout ‘luci-p910nd’
          Mon Aug 18 18:41:29 2014 kern.err kernel: overlayfs: ERROR – failed to whiteout ‘luci-theme-bootstrap’
          Mon Aug 18 18:41:29 2014 kern.err kernel: overlayfs: ERROR – failed to whiteout ‘luci-theme-openwrt’
          Mon Aug 18 18:41:29 2014 kern.err kernel: overlayfs: ERROR – failed to whiteout ‘S95miniupnpd’
          Mon Aug 18 18:41:29 2014 kern.err kernel: overlayfs: ERROR – failed to whiteout ‘luci-upnp’
          Mon Aug 18 18:41:29 2014 kern.err kernel: overlayfs: ERROR – failed to whiteout ‘odhcpd.defaults’
          Mon Aug 18 18:41:29 2014 user.emerg syslog: Error: Failed to connect to ubus
          Mon Aug 18 18:41:29 2014 user.emerg syslog: Failed to connect to the switch. Use the “list” command to see which switches are available.
          Mon Aug 18 18:41:31 2014 user.emerg syslog: this file has been obseleted. please call “/sbin/block mount” directly
          Mon Aug 18 18:41:35 2014 user.info syslog: module is already loaded – xt_comment
          Mon Aug 18 18:41:35 2014 kern.emerg already loaded – xt_comment
          Mon Aug 18 18:41:38 2014 user.info syslog: module is already loaded – xt_comment
          Mon Aug 18 18:41:38 2014 kern.emerg already loaded – xt_comment
          Mon Aug 18 18:41:40 2014 daemon.notice netifd: Interface ‘loopback’ is enabled
          Mon Aug 18 18:41:40 2014 daemon.notice netifd: Interface ‘loopback’ is setting up now
          Mon Aug 18 18:41:40 2014 daemon.notice netifd: Interface ‘loopback’ is now up
          Mon Aug 18 18:41:40 2014 daemon.notice netifd: Interface ‘lan’ is enabled
          Mon Aug 18 18:41:40 2014 daemon.notice netifd: Interface ‘lan’ is setting up now
          Mon Aug 18 18:41:40 2014 daemon.notice netifd: Interface ‘lan’ is now up
          Mon Aug 18 18:41:40 2014 kern.info kernel: IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
          Mon Aug 18 18:41:40 2014 daemon.notice netifd: Network device ‘lo’ link is up
          Mon Aug 18 18:41:40 2014 daemon.notice netifd: Interface ‘loopback’ has link connectivity
          Mon Aug 18 18:41:41 2014 user.emerg syslog: Generating RSA private key, 1024 bit long modulus
          Mon Aug 18 18:41:43 2014 kern.info kernel: IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
          Mon Aug 18 18:41:43 2014 kern.info kernel: device wlan0 entered promiscuous mode
          Mon Aug 18 18:41:47 2014 daemon.info dnsmasq[1771]: started, version 2.71 cachesize 150
          Mon Aug 18 18:41:47 2014 daemon.info dnsmasq[1771]: compile time options: IPv6 GNU-getopt no-DBus no-i18n no-IDN DHCP no-DHCPv6 no-Lua TFTP no-conntrack no-ipset no-auth no-DNSSEC
          Mon Aug 18 18:41:47 2014 daemon.info dnsmasq-dhcp[1771]: DHCP, IP range 192.168.1.100 — 192.168.1.249, lease time 12h
          Mon Aug 18 18:41:47 2014 daemon.info dnsmasq[1771]: using local addresses only for domain lan
          Mon Aug 18 18:41:47 2014 daemon.warn dnsmasq[1771]: no servers found in /tmp/resolv.conf.auto, will retry
          Mon Aug 18 18:41:47 2014 daemon.info dnsmasq[1771]: read /etc/hosts – 1 addresses
          Mon Aug 18 18:41:47 2014 daemon.info dnsmasq-dhcp[1771]: read /etc/ethers – 0 addresses
          Mon Aug 18 18:41:48 2014 user.emerg syslog: Generating selfsigned certificate with subject ‘C=DE;ST=Berlin;L=Berlin;CN=OpenWrt;’ and validity 20140818184141-20160817184141
          Mon Aug 18 18:41:50 2014 user.notice firewall: Reloading firewall due to ifup of lan (br-lan)
          Mon Aug 18 18:41:54 2014 kern.info kernel: br-lan: port 1(wlan0) entered forwarding state
          Mon Aug 18 18:41:54 2014 kern.info kernel: br-lan: port 1(wlan0) entered forwarding state
          Mon Aug 18 18:41:54 2014 kern.info kernel: IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
          Mon Aug 18 18:41:54 2014 daemon.notice netifd: Bridge ‘br-lan’ link is up
          Mon Aug 18 18:41:54 2014 daemon.notice netifd: Interface ‘lan’ has link connectivity
          Mon Aug 18 18:41:54 2014 kern.info kernel: IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
          Mon Aug 18 18:41:54 2014 user.emerg syslog: No jffs2 marker was found
          Mon Aug 18 18:41:54 2014 user.emerg syslog: No jffs2 marker was found
          Mon Aug 18 18:41:54 2014 user.emerg syslog: no jffs2 marker found
          Mon Aug 18 18:41:54 2014 kern.notice kernel: jffs2: notice: (1928) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
          Mon Aug 18 18:41:55 2014 daemon.notice netifd: Network device ‘wlan0′ link is up
          Mon Aug 18 18:41:55 2014 kern.info kernel: br-lan: port 1(wlan0) entered forwarding state
          Mon Aug 18 18:41:57 2014 user.emerg syslog: doing fo cleanup
          Mon Aug 18 18:41:57 2014 daemon.info hostapd: wlan0: STA 78:e4:00:32:ef:a8 IEEE 802.11: authenticated
          Mon Aug 18 18:41:57 2014 daemon.info hostapd: wlan0: STA 78:e4:00:32:ef:a8 IEEE 802.11: associated (aid 1)
          Mon Aug 18 18:41:57 2014 daemon.info hostapd: wlan0: STA 78:e4:00:32:ef:a8 WPA: pairwise key handshake completed (RSN)
          Mon Aug 18 18:41:57 2014 user.notice upnp daemon: external interface not found, not starting
          Mon Aug 18 18:41:57 2014 user.emerg syslog: setting up led USB
          Mon Aug 18 18:41:57 2014 user.emerg syslog: setting up led WLAN
          Mon Aug 18 18:41:57 2014 user.emerg syslog: setting up led CPU
          Mon Aug 18 18:41:58 2014 user.emerg syslog: – init complete –
          Mon Aug 18 18:42:00 2014 daemon.info dnsmasq-dhcp[1771]: DHCPDISCOVER(br-lan) 78:e4:00:32:ef:a8
          Mon Aug 18 18:42:00 2014 daemon.info dnsmasq-dhcp[1771]: DHCPOFFER(br-lan) 192.168.1.116 78:e4:00:32:ef:a8
          Mon Aug 18 18:42:00 2014 daemon.info dnsmasq-dhcp[1771]: DHCPREQUEST(br-lan) 192.168.1.116 78:e4:00:32:ef:a8
          Mon Aug 18 18:42:00 2014 daemon.info dnsmasq-dhcp[1771]: DHCPACK(br-lan) 192.168.1.116 78:e4:00:32:ef:a8 Hannspree
          Mon Aug 18 18:43:40 2014 authpriv.info dropbear[2288]: Not backgrounding
          Mon Aug 18 18:44:12 2014 user.info syslog: module is already loaded – xt_comment
          Mon Aug 18 18:44:12 2014 kern.emerg already loaded – xt_comment
          Mon Aug 18 18:45:23 2014 daemon.info dnsmasq-dhcp[1771]: DHCPRELEASE(br-lan) 192.168.1.116 78:e4:00:32:ef:a8
          Mon Aug 18 18:46:26 2014 daemon.info hostapd: wlan0: STA 78:e4:00:32:ef:a8 IEEE 802.11: authenticated
          Mon Aug 18 18:46:26 2014 daemon.info hostapd: wlan0: STA 78:e4:00:32:ef:a8 IEEE 802.11: associated (aid 1)
          Mon Aug 18 18:46:26 2014 daemon.info hostapd: wlan0: STA 78:e4:00:32:ef:a8 WPA: pairwise key handshake completed (RSN)
          Mon Aug 18 18:46:29 2014 daemon.info dnsmasq-dhcp[1771]: DHCPDISCOVER(br-lan) 192.168.43.94 78:e4:00:32:ef:a8
          Mon Aug 18 18:46:29 2014 daemon.info dnsmasq-dhcp[1771]: DHCPOFFER(br-lan) 192.168.1.116 78:e4:00:32:ef:a8
          Mon Aug 18 18:46:29 2014 daemon.info dnsmasq-dhcp[1771]: DHCPREQUEST(br-lan) 192.168.1.116 78:e4:00:32:ef:a8
          Mon Aug 18 18:46:29 2014 daemon.info dnsmasq-dhcp[1771]: DHCPACK(br-lan) 192.168.1.116 78:e4:00:32:ef:a8 Hannspree
          Mon Aug 18 18:47:46 2014 user.info syslog: module is already loaded – xt_comment
          Mon Aug 18 18:47:46 2014 kern.emerg already loaded – xt_comment
          Mon Aug 18 18:48:44 2014 daemon.info dnsmasq-dhcp[1771]: DHCPRELEASE(br-lan) 192.168.1.116 78:e4:00:32:ef:a8
          Mon Aug 18 18:48:51 2014 daemon.info hostapd: wlan0: STA 78:e4:00:32:ef:a8 IEEE 802.11: authenticated
          Mon Aug 18 18:48:51 2014 daemon.info hostapd: wlan0: STA 78:e4:00:32:ef:a8 IEEE 802.11: associated (aid 1)
          Mon Aug 18 18:48:51 2014 daemon.info hostapd: wlan0: STA 78:e4:00:32:ef:a8 WPA: pairwise key handshake completed (RSN)
          Mon Aug 18 18:48:54 2014 daemon.info dnsmasq-dhcp[1771]: DHCPDISCOVER(br-lan) 78:e4:00:32:ef:a8
          Mon Aug 18 18:48:54 2014 daemon.info dnsmasq-dhcp[1771]: DHCPOFFER(br-lan) 192.168.1.116 78:e4:00:32:ef:a8
          Mon Aug 18 18:48:54 2014 daemon.info dnsmasq-dhcp[1771]: DHCPREQUEST(br-lan) 192.168.1.116 78:e4:00:32:ef:a8
          Mon Aug 18 18:48:54 2014 daemon.info dnsmasq-dhcp[1771]: DHCPACK(br-lan) 192.168.1.116 78:e4:00:32:ef:a8 Hannspree
          Mon Aug 18 18:50:12 2014 daemon.info dnsmasq-dhcp[1771]: DHCPRELEASE(br-lan) 192.168.1.116 78:e4:00:32:ef:a8
          Mon Aug 18 18:50:14 2014 daemon.info hostapd: wlan0: STA 78:e4:00:32:ef:a8 IEEE 802.11: authenticated
          Mon Aug 18 18:50:14 2014 daemon.info hostapd: wlan0: STA 78:e4:00:32:ef:a8 IEEE 802.11: associated (aid 1)
          Mon Aug 18 18:50:14 2014 daemon.info hostapd: wlan0: STA 78:e4:00:32:ef:a8 WPA: pairwise key handshake completed (RSN)
          Mon Aug 18 18:50:17 2014 daemon.info dnsmasq-dhcp[1771]: DHCPDISCOVER(br-lan) 78:e4:00:32:ef:a8
          Mon Aug 18 18:50:17 2014 daemon.info dnsmasq-dhcp[1771]: DHCPOFFER(br-lan) 192.168.1.116 78:e4:00:32:ef:a8
          Mon Aug 18 18:50:17 2014 daemon.info dnsmasq-dhcp[1771]: DHCPREQUEST(br-lan) 192.168.1.116 78:e4:00:32:ef:a8
          Mon Aug 18 18:50:17 2014 daemon.info dnsmasq-dhcp[1771]: DHCPACK(br-lan) 192.168.1.116 78:e4:00:32:ef:a8 Hannspree
          ====================================

  31. Andrei

    Salut, am si eu un 1043ND v1, cu OpenWrt momentatn si vad ca imi face figuri ( nu imi aloca IP pe wifi acum). Imi poti spune daca versiunea de firmwere de la voi ( v2) merge si pe v1? Multumesc frumos.

    1. SuperWrt Geek

      Salut Andrei,
      o să adaug (iar) în weekend și firmware pentru v1 pentru că observ mai mulți vizitatori care (încă) mai folosesc versiunea veche de router..

      1. Paul

        Multumim pentru ajutor! Chiar mai suntem multisori pe aici care mai folosesc 1043ND v1!
        Chiar am vrut eu sa te rog sa mai introduci updateuri de firmware pentru v1!

  32. Bogdan

    Multumim pentru 1043ND v1!

  33. Paul

    Multumim pentru firmware-ul 1043ND v1! Are cumva si Luci compilat?

    1. SuperWrt Geek

      Salut Paul, evident c-are și suita LuCi integrată. Am adăugat lista de pachete instalate în pagina routerului, poți da click pe butonul cu “click pentru pachetele pre-instalate” să vezi exact ce conține firmware-ul..

  34. Costi

    Salut.
    1043ND v1, dupa luni bune de folosit r41393 am trecut si eu la r42258, dar vad ca la testul de ipv6 nu trece.

    1. Costi

      Cred ca a fost o problema cu site-ul. Acum merge; in router aveam de ieri ip6 dat de RDS

  35. Romica

    Pe r42434, wr1043nd v2.1, nu merge swap:

    swapon /dev/sda2
    block: failed to swapon /dev/sda2 (-1)

    1. SuperWrt Geek

      Salut Romica,
      am dezactivat permanent facilitatea de swap direct în kernel, nu există nici un motiv pentru care se mai justifică folosirea swap pe un echipament de tip router, nici măcar via zram.

      1. Romica

        Multumesc pt. raspuns! Ma gandeam poate sunt probleme cu transmission, mananca destul de mult ram.

        1. SuperWrt Geek

          N-aș rula transmission pe un echipament cu mai puțin de 128 MB de ram gen wdr3600/wdr4300/wdr4900 ..
          Mai precis – nu cred că există vreun NAS pur cu transmission cu mai puțin de 128 MB de ram pe placa de bază.. Seagate GoFlex mi se pare cel mai slabuț. De obicei NAS-urile dotate cu un client de torrent au 256 ori 512 MB de ram.

          1. Romica

            L-am folosit de cateva ori pana acum. Plus ca mai am si proftpd pe el… in fine, daca nu e, vad eu ce fac. As schimba kernelul, dar trebuie sa compilez si module etc… si timp ioc. Mi-ar fi de folos daca ai reactiva swap-ul. Multumesc!
            PS: buna treaba cu superwrt!

          2. Stefan

            Sustin si eu ideea lui Romica de a reactiva swap-ul.

            @SuperWrt
            Se poate reactiva swap-ul in urmatorul build?

          3. SuperWrt Geek

            Da Ștefan, o să adaug și modulul de kernel pentru zram pentru cei care doresc să-și configureze swap-ul în memoria ram :)

          4. Stefan

            Multumesc pt reactivarea swap-ului.

            Acum fac un sysupgrade

          5. Stefan

            Swap-ul mai este activ pe build-ul SuperWrt (Barrier Breaker 14.07) Firmware r42961 – kernel 3.10.49?

            Am incercat, dar fara succes

  36. Romica

    Salut, as vrea sa-mi compilez firmware-ul. Poti sa-mi trimiti, te rog, “.config”, sa am macar ce e in superwrt?
    Multumesc!

  37. Cristi

    Salut! Folosesc varianta 2 a acestui router cu ultima versiune oficiala de FW. Totodata, am un Fiberlink 500 ca solutie de net. Am cateva intrebari:
    1) daca instalez varianta ta de FW, in cazul in care nu-mi place cum fac sa revin la varianta stock?
    2) exista vreo sansa in viitor sa poata fi activat NAT Hardware ca in FW original?
    3) din experienta ta, cat de stabila a devenit conexiunea WiFi la distante de peste 50 m? Momentan, un 841 ND bate la fund un 1043 ND din punctul asta de vedere. Tocmai am testat cele doua routere weekendul asta ( teste efectuate la circa 50 m, cu vedere directa la cele doua routere, atat cu laptopul, cat si cu 2 telefoane mobile).

  38. dan

    Salut,

    M-am apucat sa fac update la ultima versiune si se pare ca ceva e stricat in repo si in alta parte pentru ca imi da o gramada de erori.
    Scuza-mi limbajul dar nu prea ma pricep.

    root@UnknowN:~# opkg update
    Downloading http://downloads.openwrt.org/snapshots/trunk/ar71xx/packages/base/Packages.gz.
    Updated list of available packages in /var/opkg-lists/barrier_breaker_base.
    Downloading http://downloads.openwrt.org/snapshots/trunk/ar71xx/packages/telephony/Packages.gz.
    Updated list of available packages in /var/opkg-lists/barrier_breaker_telephony.
    Downloading http://downloads.openwrt.org/snapshots/trunk/ar71xx/packages/oldpackages/Packages.gz.
    wget: server returned error: HTTP/1.1 404 Not Found
    Downloading http://downloads.openwrt.org/snapshots/trunk/ar71xx/packages/packages/Packages.gz.
    Updated list of available packages in /var/opkg-lists/barrier_breaker_packages.
    Downloading http://downloads.openwrt.org/snapshots/trunk/ar71xx/packages/routing/Packages.gz.
    Updated list of available packages in /var/opkg-lists/barrier_breaker_routing.
    Downloading http://downloads.openwrt.org/snapshots/trunk/ar71xx/packages/luci/Packages.gz.
    Updated list of available packages in /var/opkg-lists/barrier_breaker_luci.
    Downloading http://downloads.openwrt.org/snapshots/trunk/ar71xx/packages/management/Packages.gz.
    Updated list of available packages in /var/opkg-lists/barrier_breaker_management.
    Collected errors:
    * opkg_download: Failed to download http://downloads.openwrt.org/snapshots/trunk/ar71xx/packages/oldpackages/Packages.gz, wget returned 1.
    root@UnknowN:~# opkg install nano
    Package nano (2.3.6-1) installed in root is up to date.
    Configuring terminfo.
    //usr/lib/opkg/info/terminfo.postinst: line 4: default_postinst: not found
    Configuring libltdl.
    //usr/lib/opkg/info/libltdl.postinst: line 4: default_postinst: not found
    Configuring collectd.
    //usr/lib/opkg/info/collectd.postinst: line 4: default_postinst: not found
    Configuring librrd1.
    //usr/lib/opkg/info/librrd1.postinst: line 4: default_postinst: not found
    Configuring rrdtool1.
    //usr/lib/opkg/info/rrdtool1.postinst: line 4: default_postinst: not found
    Configuring collectd-mod-rrdtool.
    //usr/lib/opkg/info/collectd-mod-rrdtool.postinst: line 4: default_postinst: not found
    Configuring collectd-mod-iwinfo.
    //usr/lib/opkg/info/collectd-mod-iwinfo.postinst: line 4: default_postinst: not found
    Configuring collectd-mod-interface.
    //usr/lib/opkg/info/collectd-mod-interface.postinst: line 4: default_postinst: not found
    Configuring collectd-mod-load.
    //usr/lib/opkg/info/collectd-mod-load.postinst: line 4: default_postinst: not found
    Configuring collectd-mod-network.
    //usr/lib/opkg/info/collectd-mod-network.postinst: line 4: default_postinst: not found
    Configuring luci-app-statistics.
    //usr/lib/opkg/info/luci-app-statistics.postinst: line 4: default_postinst: not found
    Configuring libncurses.
    //usr/lib/opkg/info/libncurses.postinst: line 4: default_postinst: not found
    Configuring nano.
    //usr/lib/opkg/info/nano.postinst: line 4: default_postinst: not found
    Configuring libext2fs.
    //usr/lib/opkg/info/libext2fs.postinst: line 4: default_postinst: not found
    Configuring e2fsprogs.
    //usr/lib/opkg/info/e2fsprogs.postinst: line 4: default_postinst: not found
    Configuring fdisk.
    //usr/lib/opkg/info/fdisk.postinst: line 4: default_postinst: not found
    Collected errors:
    * pkg_run_script: package “terminfo” postinst script returned status 127.
    * opkg_configure: terminfo.postinst returned 127.
    * pkg_run_script: package “libltdl” postinst script returned status 127.
    * opkg_configure: libltdl.postinst returned 127.
    * pkg_run_script: package “collectd” postinst script returned status 127.
    * opkg_configure: collectd.postinst returned 127.
    * pkg_run_script: package “librrd1″ postinst script returned status 127.
    * opkg_configure: librrd1.postinst returned 127.
    * pkg_run_script: package “rrdtool1″ postinst script returned status 127.
    * opkg_configure: rrdtool1.postinst returned 127.
    * pkg_run_script: package “collectd-mod-rrdtool” postinst script returned status 127.
    * opkg_configure: collectd-mod-rrdtool.postinst returned 127.
    * pkg_run_script: package “collectd-mod-iwinfo” postinst script returned status 127.
    * opkg_configure: collectd-mod-iwinfo.postinst returned 127.
    * pkg_run_script: package “collectd-mod-interface” postinst script returned status 127.
    * opkg_configure: collectd-mod-interface.postinst returned 127.
    * pkg_run_script: package “collectd-mod-load” postinst script returned status 127.
    * opkg_configure: collectd-mod-load.postinst returned 127.
    * pkg_run_script: package “collectd-mod-network” postinst script returned status 127.
    * opkg_configure: collectd-mod-network.postinst returned 127.
    * pkg_run_script: package “luci-app-statistics” postinst script returned status 127.
    * opkg_configure: luci-app-statistics.postinst returned 127.
    * pkg_run_script: package “libncurses” postinst script returned status 127.
    * opkg_configure: libncurses.postinst returned 127.
    * pkg_run_script: package “nano” postinst script returned status 127.
    * opkg_configure: nano.postinst returned 127.
    * pkg_run_script: package “libext2fs” postinst script returned status 127.
    * opkg_configure: libext2fs.postinst returned 127.
    * pkg_run_script: package “e2fsprogs” postinst script returned status 127.
    * opkg_configure: e2fsprogs.postinst returned 127.
    * pkg_run_script: package “fdisk” postinst script returned status 127.
    * opkg_configure: fdisk.postinst returned 127.
    root@UnknowN:~#

    Cam asta e, multumesc.

  39. john

    nuprea mai merge sa fac revenire la stock pe wr1043nd v1
    dau fisierul si nu mai reactioneaza router-ul, nu apare pagina de confirmare pentru flash…

    1. SuperWrt Geek

      Îmi pare rău dar nu mai am un wr1043nd v1. Am și precizat mai sus:
      Atenție ! Nu mai am versiunea asta hardware de router și nu mai pot testa firmware-ul dar ar trebui să funcționeze.. Folosiți pe propria răspundere !

  40. john

    asta am inteles, eu sunt pe openwrt de vreo 2 ani si as vrea sa trec pe stock sau altceva deoarece ultimile versiuni cauzeaza instabilitate; probleme de wireless sau pierdere setari
    problema e ca nu reusesc sa pun innapoi stock
    ce as putea incerca sa scap de aceasta problema?
    eventual downgrade la un openwrt mai vechi dar nu am de unde descarca

  41. john

    nvm a reusit intr-un final cu opera, chrome nu serveste

    1. SuperWrt Geek

      Salut Costi,
      ori editezi /etc/opkg.conf și corectezi repo url ori în weekend actualizez eu firmware-ul.

      1. Costi

        Salut!

        Chiar daca scot repo-ul cu probleme, tot ramane problema cu ssmtp pe care nu il mai gasesc si motion care se instaleaza, dar nu functioneaza.

        Merci!

  42. Tugurlan

    salut,

    in primul rand multumesc pentru efortul depus.

    in al doilea rand, pe ultima versiune de firmware pentru hd rev 1, desi instalez watchcat, acesta nu apare la configurare sub tabul de services. Imi poti spune te rog cum il pot configura altfel?

    As vrea ca routerul sa faca un hard reboot in momentul in care providerul de net nu mai furnizeaza.

    Multumesc.

      1. Tugurlan

        Mersi pt raspunsul prompt, l-am instalat.

        Acum, tot ce mai lipseste e o solutie de adblocking pe router… Am incercat cu privoxy, dar in momentul in care pornesc proxy-ul, routerul crapa in 2 minute maxim (1043nd).

        Ai cumva o solutie mai eleganta? :) Am mai multe device-uri pe lan (fizic si wifi) si as vrea sa nu fie nevoie sa explic intregii familii cum e cu adblock in browser… plus ca lumea nu vrea reclame la filmele pe youtube! :)

        Iaodi, incearca sa introduci un sistem de donatii pe pagina, poate paypal. Sunt sigur ca e multa lume care ar vrea sa te recompenseze direct, nu doar prin profitshare la emag.

          1. Tugurlan

            perfect, ms.

            eventual si pentru versiunile urmatoare o functie simpla de DMZ, fara creat vlan… asa, mura-n gura :).

        1. Costi

          Salut!

          Eu folosesc asa ceva:

          Remove ads

          First File: /etc/firewall.user (Make a copy of the file before editing)
          Add this 2 lines:

          iptables -t nat -I PREROUTING -p tcp –dport 53 -j REDIRECT –to-ports 53
          iptables -t nat -I PREROUTING -p udp –dport 53 -j REDIRECT –to-ports 53

          Add the following line into /etc/config/dhcp, under the section “config dnsmasq”:

          list addnhosts ‘/tmp/block.host’

          Then add these to /etc/rc.local to populate the block list during startup automatically, or use your own source URLs:

          (
          wget -qO- http://www.mvps.org/winhelp2002/hosts.txt|grep “^127.0.0.1″ > /tmp/block.host
          wget -qO- http://someonewhocares.org/hosts/hosts|grep “^127.0.0.1″ >> /tmp/block.host
          wget -qO- http://www.malwaredomainlist.com/hostslist/hosts.txt|grep “^127.0.0.1″ >> /tmp/block.host
          sort /tmp/block.host|uniq -u >/tmp/sorted
          mv /tmp/sorted /tmp/block.host
          /etc/init.d/dnsmasq restart ) &

          Faci un script si il rulezi periodic eventual.

          Spor!

  43. tzepii

    Salut

    in primul rand felicitari pentru distributie.
    Nu sunt familiarizat cu linux-ul si nu reusesc sa atasez un hdd extern formatat NTFS:
    Acesta este o parte din log:
    SCSI subsystem initialized
    ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
    ehci-platform: EHCI generic platform driver
    ehci-platform ehci-platform.0: EHCI Host Controller
    ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1
    ehci-platform ehci-platform.0: TX-TX IDP fix enabled
    ehci-platform ehci-platform.0: irq 48, io mem 0x1b000000
    ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00
    hub 1-0:1.0: USB hub found
    hub 1-0:1.0: 1 port detected
    ehci-platform ehci-platform.1: EHCI Host Controller
    ehci-platform ehci-platform.1: new USB bus registered, assigned bus number 2
    ehci-platform ehci-platform.1: TX-TX IDP fix enabled
    ehci-platform ehci-platform.1: irq 49, io mem 0x1b400000
    ehci-platform ehci-platform.1: USB 2.0 started, EHCI 1.00
    hub 2-0:1.0: USB hub found
    hub 2-0:1.0: 1 port detected
    ohci_hcd: USB 1.1 ‘Open’ Host Controller (OHCI) Driver
    usbcore: registered new interface driver usb-storage
    usb 1-1: new high-speed USB device number 2 using ehci-platform
    usb-storage 1-1:1.0: USB Mass Storage device detected
    scsi0 : usb-storage 1-1:1.0
    eth1: link up (1000Mbps/Full duplex)
    scsi 0:0:0:0: Direct-Access Seagate Expansion Desk 0319 PQ: 0 ANSI: 6
    sd 0:0:0:0: [sda] 3907029167 512-byte logical blocks: (2.00 TB/1.81 TiB)
    sd 0:0:0:0: [sda] Write Protect is off
    sd 0:0:0:0: [sda] Mode Sense: 2b 00 10 08
    sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, supports DPO and FUA
    sda: sda1
    sd 0:0:0:0: [sda] Attached SCSI disk
    jffs2: notice: (371) jffs2_build_xattr_subsystem: complete building xattr subsystem, 5 of xdatum (1 unchecked, 4 orphan) and 37 of xref (0 dead, 11 orphan) found.
    jffs2: notice: (368) jffs2_build_xattr_subsystem: complete building xattr subsystem, 5 of xdatum (1 unchecked, 4 orphan) and 37 of xref (0 dead, 11 orphan) found.
    eth1: link down
    NET: Registered protocol family 10
    NTFS driver 2.1.30 [Flags: R/O MODULE].
    tun: Universal TUN/TAP device driver, 1.6
    tun: (C) 1999-2004 Max Krasnyansky
    sit: IPv6 over IPv4 tunneling driver
    gre: GRE over IPv4 demultiplexor driver

    in system -> mount point, cand dau add apare in dropdown dev/sda si dev/sda1, ambele de aceeasi dimensiune. Indiferent pe care o aleg, nu apare in Mounted file systems.
    Ce fac gresit?

    Multumesc

    1. SuperWrt Geek

      Sigur e ntfs? /dev/sda1 îl montezi. Ai dat save & apply? comanda mount via ssh ce arată?

  44. tzepii

    Salut

    Sigur este ntfs. Am dat si save si restart. Daca-l montez din shell, il vad in folderul respectiv (tot in shell), dar nu vad maparea in interfata luci. Configurat Samba, imi spune ca nu am drepturi de acces cand incerc sa intru pe share. Hdd-ul este de 2Tb (care am inteles ca este limita maxima) dar fizic are undeva la 1.8Tb. Totusi cu mount manual pare sa fie ok. Eroarea de drepturi sa aiba legatura cu faptul ca l-am montat logat ca root?

    Multumesc

  45. Tugurlan

    Salut,

    Am un router 1043ND v1 si nu pot reveni la default. In momentul in care dau flash firmware, in loc sa primesc prompt-ul cu informatiile despre firmware-ul urcat, routerul crapa si se restarteaza…

    Ai idee ce se intampla?

    Ms.

    1. Tugurlan

      Nu pot scrie firmware-ul original. Daca insa folosesc optiunea de upgrade, totul merge ok.

  46. Dekonass

    I have tp-link wr1043nd V2.1 and your firmware it works fine (wifi, and lan, etc).

    Could you help me please, how to configure “dual wan” ?

  47. cezar

    Salut,

    NAT hardware este util si pe partea de wifi, sau doar pe fir ?

  48. tzepii

    Salut

    3 intrebari de incepator:
    E posibil sa dezactivez IPv6, si daca da cum (poate considerui ca merita un minitutorial)?
    Cum pot vedea versiunea de kernel care este in build-ul de update?
    Pot sa fac sa un job care sa restarteze automat routerul in fiecare noapte (nu stiu de ce, dar cand ajung acasa il gasesc agatat)

    Multumesc.

    1. SuperWrt Geek

      Salut, cu “option ipv6 0″ în feluritele configuri, pentru kernel există “uname -a” iar pentru restart poți instala și folosi watchcat (luci-app-watchcat).

      1. tzepii

        Multumesc frumos pentru raspunsuri.

        Pentru kernel, eu intrebam cum pot vedea versiunea care este in bin-ul pe care-l descarc de pe aceasta pagina, nu versiunea pe care o am instalata pe router. Am instalat bin-ul de upgrade, crezand ca este versiunea care apare in headerul paginii, adica “SuperWrt (Barrier Breaker 14.07) Firmware r42961 – kernel 3.10.49″ dar nu este o versiune mai mica.

  49. Pifu Valentin

    Salut.
    Am si eu o intrebare. Am vechiul 1043ND si din pacate mi-am schimbat abonamentul la FB500.
    Intrebare este urmatoarea: exista vreun custom firmware care sa aibe hardware nat – on si sa treaca de 300mbps ?

    Multumesc.

  50. cezar

    O alta intrebare de baraj : firmaware-ul original nu permite decat bgn mixed, nu n only. Superwrt rezolva cumva chestia asta, ca observ semnal pe wi fi mai slab ca vechiul 1043.

  51. licurici

    ziceai ceva la un moment dat de “repo for extra modules” . ma intereseaza modulul kmod-usb-serial-cp210x . folosesc un 1043nd v1. merci

Leave a Reply